Please read carefully before installing components.
ME-0725-PS-215-B 09-08 FDP/ID
INSTALLATION DATA FOR MICRO SERIES DISTRIBUTOR TUBES,
REFER TO MINI-PRINT NO. 1700
END CAP, HEATERS AND AUTO-FIXED "INTEGRAL HEATER"
DISTRIBUTOR PROBES, END CAPS.
R
FULL RAD.
B DIA. ±0.002
E
±0.010
0.500 ±0.002
C DIA. -0.002
0.000
D DIA.
-0.005
0.000
0.50
±0.005
L
probe, but in no way alters its
MATERIAL, S-7 STEEL OR EQUIVALENT WITH 32-34 Rc HARDNESS.
AUTO-FIXED "INTEGRAL HEATER" DISTRIBUTOR PROBES
R
(240 VAC, T/C TYPE J, LEADS ARE 34" LONG AND 90 )
REPLACEMENT THERMOCOUPLE
(ALL PROBES)
NOTE: PROBE DISCOLORATION
Each Integral Heater probe sold by
D-M-E is pre-tested. This procedure
discolors the outer surface of the
performance or dimensions.
D
E
D
E
B
A
0.25 x 45 (4)
F
0.25
1.125
C
END CAPS FOR DISTRIBUTOR PROBES
2 PIECE CONSTRUCTION
DRILLED AND
C'BORED FOR
2 PIECE CONSTRUCTION
# 3/8-16 S.H.C.S
# THREAD ENGAGEMENT INTO MOLD MUST BE 1.00 MINIMUM AND TORQUED TO
25-30 FOOT POUNDS.
MATERIAL, AISI 4140 STEEL OR EQUIVALENT WITH 28-35 Rc HARDNESS
0.005 TYP.
45°
0.005 TYP.
RECOMMENDED RELATIONSHIP BETWEEN
NOTE: - S SPLIT LINE OF MOLD
L
S
L
DISTRIBUTOR PROBE AND SUPPORT PINS
0.39
0.75
MIN.
1.00
MIN.
SEE
NOTE #2
0.080
±0.010
0.750
1.000
MIN.
0.250
Z
Y
X
0.562
SEE
NOTE #3
0.093
0.25 MAX
2.187 MIN.
2.750 MAX.
SEE NOTE #1
0.093
0.750
MIN.
1.187 MIN.
1.750 MAX.
SEE NOTE #1
0.080 PLUS DISTRIBUTOR PROBE EXPANSION
ON ALL DISTRIBUTOR PROBE INTERSECTIONS
0.250 RAD.0.250 RAD.
TYP. TYP.
MICHIGAN 48071 USA
1-800-626-6653
29111 STEPHENSON HIGHWAY
MADISON HEIGHTS
www.dme.net
D-M-E COMPANY
Note: Dimensions shown in Inches.
X
MIN.
Y
MIN.
Z
MIN.
PROBES, INTERSCTIONS AND END CAPS
RECOMMENDED RELATIONSHIP BETWEEN HEATERS,
0.394 DIA. 0.788 0.500 1.375
0.625 DIA. 1.250
between dowel pin and end cap centerlines is recommended
3. The use of (2) 0.250 dia. dowel pins with 0.562 distance
(Solid Block Distributor System only).
to secure end cap into mold
evenly and torqued to 25-30 foot pounds.
Split Plate Distributor System) Screws must be tightened
-mended to secure end caps to mold. (Solid Block and
with 1.00 minimum thread engagement into mold is recom
2. The use of (4) 3/8-16 hardened socket head cap screws
will not be centered in distributor tube.
1. Due to the longer no heat section atthe Lead end, heater
NOTES:
0.875 1.375
FDP0017 8.500 0.009 670
FDP0018 9.000 0.009 705
FDP0019 9.500 0.010 745
FDP0020 10.000 0.010 785
+0.010
2.000
1.98B
-0.000
+0.010
2.500
2.49
-0.000
+0.010
2.000
1.98A
MACHINING
0.625 DIA.
PROBE
DISTRIBUTOR
0.625 DIA.
MACHINING
0.394 DIA.
PROBE
DISTRIBUTOR
0.394 DIA.
DIM
ECP0006ECP0003CAT. NO.
-0.875-0.500F
0.3750.375
0.2210.625 DIA.
0.1390.394 DIA.
48"TC-9900
LEAD LENGTHCATALOG NUMBER
X
PROBE
DISTRIBUTOR
0.4370.437E
0.8750.8750.6560.656D
-0.000
+0.001
1.125
1.124
-0.000
+0.001
0.875
0.874C
-0.000
+0.010
2.000
1.98
-0.000
CAT.
NO.
L
EXPAN-
SION
WATTSAB CDE
FDP0001 3.500 0.004 175
0.394 0.384 0.740 0.394 0.750
FDP0002 4.000 0.004 200
FDP0003 4.500 0.005 225
FDP0004 5.000 0.005 250
FDP0005 5.500 0.006 275
FDP0006 6.000 0.006 295
FDP0007 6.500 0.007 320
FDP0008 4.000 0.004 315
0.625 0.615 1.240 0.625 1.125
FDP0009 4.500 0.005 355
FDP0010 5.000 0.005 395
FDP0011 5.500 0.006 430
FDP0012 6.000 0.006 470
FDP0013 6.500 0.007 510
FDP0014 7.000 0.007 550
FDP0015 7.500 0.008 590
FDP0016 8.000 0.008 630
DISTRIBUTOR
PROBE
(1 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern